Installation Instruction

Stickers&Decals

1. Prepare the Surface: Thoroughly clean the hood surface where you'll be applying the decals. Use a mild detergent or automotive soap and water to remove any dirt, grease, wax, or residue. Rinse the area with clean water and ensure it is completely dry before proceeding.

2. Positioning: Before removing the backing paper from the decal, carefully position it in your desired location using masking tape or painter's tape. This step allows you to ensure proper alignment and spacing of the decals before applying them.

3. Peel Off the Backing Paper: Starting from one corner, gently peel off the backing paper from the decal, exposing the adhesive side. Be careful not to touch the adhesive surface with your fingers, as this can affect adhesion and cleanliness.

4.Application: Carefully place the decal onto the desired location, aligning it according to your pre-determined positioning. Use a squeegee, credit card, or soft cloth to smooth out the decal, starting from the center and working your way outward. This helps to remove any air bubbles and ensures proper adhesion to the surface.

5. Remove the Transfer Tape: Once the decal is firmly in place, slowly peel off the transfer tape from the decal, leaving the vinyl decal to adhere to its new home.

6. Press Firmly: After removing the transfer tape, press down firmly on the entire surface of the decal using a squeegee or your hand. This helps to ensure optimal adhesion and prevents any edges from lifting.

7. Repeat for Additional Decals: If your set includes multiple decals, repeat the above steps for each additional decal, ensuring proper alignment and spacing between them.

8. Allow for Proper Cure Time: Allow the decals to set and cure for at least 24 hours before exposing them to water or harsh weather conditions. This allows the adhesive to fully bond with the surface and ensures long-lasting durability. 

9. Final Touches: Once the decals are fully installed and cured, inspect the edges and corners for any signs of lifting or air bubbles. If necessary, gently press down on any lifted areas to secure them firmly to the surface. 

10. Enjoy Your Customized Look: With the installation complete, step back and admire the enhanced aesthetics of your car. Take pride in your personalized ride and enjoy the attention it garners on the road!

 

Reflective Stickers

1. Prepare the Surface: Thoroughly clean the hood surface where you'll be applying the decals. Use a mild detergent or automotive soap and water to remove any dirt, grease, wax, or residue. Rinse the area with clean water and ensure it is completely dry before proceeding.

2. Positioning: Before removing the backing paper from the reflective sticker, carefully position it in your desired location using masking tape or painter's tape. This step allows you to ensure proper alignment and spacing of the products before applying them.

3. Peel Off the Backing Paper: Starting from one corner, gently peel off the backing paper from the decal, exposing the adhesive side. Be careful not to touch the adhesive surface with your fingers, as this can affect adhesion and cleanliness. Unlike our decals, our reflective stickers are thick and sturdy, ensuring they hold their shape and won't bend easily. This feature eliminates the concern of accidentally having the adhesive surfaces stick together while positioning the sticker.

4. Application: Carefully place the decal onto the desired location, aligning it according to your pre-determined positioning. Our reflective stickers can be smoothed out by hand, no need for the use of a squeegee, starting from the center and working your way outward. This helps to remove any air bubbles and ensures proper adhesion to the surface.

5. Press Firmly: After removing the transfer tape, press down firmly on the entire surface of the sticker using your hand. This helps to ensure optimal adhesion and prevents any edges from lifting.

6. Repeat for Additional Reflective Stickers: If your set includes multiple reflective stickers, repeat the above steps for each additional product, ensuring proper alignment and spacing between them.

7. Allow for Proper Cure Time: Allow the stickers to set and cure for at least 24 hours before exposing them to water or harsh weather conditions. This allows the adhesive to fully bond with the surface and ensures long-lasting durability. 

8. Final Touches: Once the products are fully installed and cured, inspect the edges and corners for any signs of lifting or air bubbles. If necessary, gently press down on any lifted areas to secure them firmly to the surface.  

 

Car Vinyl Wraps

Preparing the Car:
- Thoroughly clean the surface of the car with soap and water to remove any dirt, grease, or wax. Dry the surface completely with a clean cloth.
- If necessary, use rubbing alcohol to remove any remaining residue and ensure a clean, smooth surface for the vinyl wrap to adhere to.

Measuring and Cutting the Vinyl Wrap:
- Measure the area of the car you want to wrap using a tape measure. Add a few inches of excess material to ensure full coverage.
- Roll out the vinyl wrap on a clean, flat surface and use a sharp utility knife or scissors to cut the wrap to the desired size and shape, allowing for additional material around the edges for trimming.

Applying the Vinyl Wrap:
- Begin by peeling a small portion of the backing paper away from the vinyl wrap, exposing the adhesive side.
- Carefully position the exposed portion of the vinyl wrap on the car, ensuring it is aligned correctly and smoothly. Use a squeegee to press down on the vinyl wrap, starting from the center and working your way outwards to remove any air bubbles and ensure a smooth application.
- Continue peeling away the backing paper and applying the vinyl wrap in small sections, using the squeegee to smooth out any wrinkles or bubbles as you go.

Trimming and Wrapping Around Edges:
- Once the vinyl wrap is fully applied to the car, use a heat gun or hairdryer on low heat to gently warm the wrap and activate the adhesive, making it more pliable.
- Use the heat gun and a squeegee to carefully wrap the excess material around the edges of the car, ensuring a tight and secure fit. Trim any excess material with a sharp utility knife or scissors for a clean finish.

Finishing Touches:
- Once the vinyl wrap is fully installed and trimmed, go over the entire surface with a squeegee to ensure proper adhesion and smooth out any remaining air bubbles or wrinkles.
- Allow the vinyl wrap to cure for at least 24 hours before washing the car or exposing it to rain or harsh weather conditions.

Maintenance and Care:
- To maintain the appearance of the vinyl wrap and prolong its lifespan, avoid using abrasive cleaners or harsh chemicals when washing the car. Instead, use a mild detergent and water, and avoid high-pressure washing.
- Regularly inspect the vinyl wrap for any signs of damage or lifting, and address any issues promptly to prevent further damage.

Follow these detailed installation instructions carefully to ensure a seamless and professional-looking application of your Bescar products.